Page 1 of 3 123 LastLast
Results 1 to 10 of 22

Thread: Finally there....

  1. #1
    Join Date
    Jun 2010
    Location
    Croton, Ohio (about a half hour NE of Columbus)
    Posts
    154

    Finally there....

    I have finally finished the setup and am now ready to commence making some messes. Thought I'd get a few shots to share beforehand. The building is a whopping 13' x 18' so I had to get a little creative in order to make the best use of the space. I'll let the pictures speak for themselves.
    Attached Thumbnails Attached Thumbnails Outside.jpg   Woodshop-1.jpg   Woodshop-2.jpg   Woodshop-3.jpg   Woodshop-4.jpg  

    Woodshop-5.jpg   Woodshop-6.jpg   Woodshop-7.jpg   Woodshop-8.jpg   Woodshop-9.jpg  

    Last edited by Roy Bauman; 07-16-2011 at 11:11 PM.

  2. #2
    Join Date
    Jun 2010
    Location
    Croton, Ohio (about a half hour NE of Columbus)
    Posts
    154
    Here's a few more closeup shots. (along with a couple of minor gloats)
    Attached Thumbnails Attached Thumbnails Work Bench-Outfeed Table.jpg   Tool Chest 1.jpg   Tool Chest 2.jpg   Router Table.jpg   Router table fence.jpg  

    Compressor-Air Tool Space.jpg   Clamp Storage Above.jpg   Clamp Storage Below.jpg   Odds and Ends.jpg   Combo-Square case.jpg  


  3. #3
    Join Date
    Aug 2007
    Location
    Reno NV
    Posts
    13,360
    Now thats a nice tidy little shop you've got there!

    Now go mess it up some!
    Programmer - An organism that turns coffee into software.
    If all your friends are exactly like you, What an un-interesting life it must be.
    "A door is what a dog is perpetually on the wrong side of" Ogden Nash


  4. #4
    Join Date
    Dec 2007
    Location
    Los Angeles, CA
    Posts
    2,668
    Roy, that is nice little man cave you have there.
    Chinese Proverb: Man who eats many prunes gets good run for the money.

  5. #5
    Join Date
    Oct 2006
    Location
    ABQ NM
    Posts
    30,014
    You did a great job with the limited space you have.
    When the going gets weird, the weird turn pro. - Hunter S. Thompson
    When the weird get going, they start their own forum. - Vaughn McMillan

    workingwoods.com

  6. #6
    Join Date
    Nov 2006
    Location
    Oak Harbor Washington on Whidbey Island
    Posts
    3,134
    Looks great....so when you going to make your first set of kitchen cabinets?

    May I ask what is in the corner behind the door is by the drill-press?

    I am always curious especially when the shop is small & a corner is used up but not by the inside of the shop.
    Last edited by Bart Leetch; 07-19-2011 at 03:49 AM.
    "Forget the flat stuff slap something on the spinny thing and lets go, we're burning daylight" Bart Leetch
    "If it ain't round you may be a knuckle dragger""Turners drag their nuckles too, they just do it at a higher RPM"Bart

  7. #7
    Join Date
    Jul 2009
    Location
    Amherst, New Hampshire
    Posts
    10,604
    Great set up
    Faith, Hope & Charity

  8. #8
    Join Date
    Sep 2007
    Location
    Plainwell, Michigan
    Posts
    4,857
    Well thought out and nice use of your space Roy Now commence making some messes and don't forget to show us what you make

  9. #9
    Join Date
    Feb 2007
    Location
    North West Indiana
    Posts
    6,098
    You have utilized that space in an amazing way!
    Those minor gloats , nothing minor! Great work!!!
    Jon

    God and family, the rest is icing on the cake. I'm so far behind, I think I'm in first place!

    Host of the 2015 FAMILY WOODWORKING GATHERING

  10. #10
    Join Date
    Sep 2010
    Location
    Trenton , Mi
    Posts
    1
    That is a nice shop. I really like that setup. Time to mess it up.

Similar Threads

  1. New car, finally.
    By Carol Reed in forum Off Topic Discussion
    Replies: 23
    Last Post: 09-26-2014, 03:50 AM
  2. Finally a day off
    By Jim Burr in forum Lathe Project Showcase
    Replies: 7
    Last Post: 04-21-2009, 05:36 AM
  3. finally done - almost
    By Paul Hubbman in forum Flatwork Project Showcase
    Replies: 13
    Last Post: 01-24-2009, 06:29 PM
  4. Finally here
    By Chris McDowell in forum Welcome and Introductions
    Replies: 15
    Last Post: 09-29-2007, 05:50 AM
  5. Finally!
    By Jay Lock in forum Welcome and Introductions
    Replies: 5
    Last Post: 11-02-2006, 03:07 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •