Page 1 of 2 12 LastLast
Results 1 to 10 of 17

Thread: jardiniere stand

  1. #1
    Join Date
    Dec 2008
    Location
    falcon heights, minnesota
    Posts
    5,610

    jardiniere stand

    now that the boards have been finally been planed to thickness, i started cutting the parts for the jardiniere stand. starting with the top, then the feet, upper supports, and legs. got the legs glued up, and tomorrow it will be the turn of the top to be glued up.
    Attached Thumbnails Attached Thumbnails 001 jardiniere design.jpg   002 jardiniere top parts cut.jpg   003 jardiniere feet cut.jpg   004 jardiniere leg parts cut.jpg   005 jardiniere legs in clamps.jpg  

    006 jardiniere top ready to be glued up.jpg  
    Last edited by Dan Noren; 06-19-2014 at 03:20 AM.
    benedictione omnes bene

    www.burroviejowoodworking.com

    check out my etsy store, buroviejowoodworking

  2. #2
    Join Date
    Dec 2008
    Location
    falcon heights, minnesota
    Posts
    5,610
    a bit more work done on the jardiniere stand today. glued up the top, glued the foot pads to the feet, and planed the legs to size and cut them to length. the only things left before finishing, is to cut the half laps and mortises for the legs in the feet, and cut the mortises for the cross members and tenons on the legs, and cut the half laps, arcs, and tenons on the cross members.
    Attached Thumbnails Attached Thumbnails 007 top glued up and in clamps.jpg   008 feet glued up.jpg   009 legs planed and cut to size.jpg   010 test set up.jpg  
    benedictione omnes bene

    www.burroviejowoodworking.com

    check out my etsy store, buroviejowoodworking

  3. #3
    Join Date
    Mar 2014
    Location
    Humid Gulf Coast
    Posts
    542
    Ah--jardiniere is just a fancy word for plant stand. Had to look that one up.

    It's looking good.

    I remember in old cowboy movies some character calling a piano, a pie-ann-y.

    I think it was Festus on Gunsmoke.

    I thought maybe jardiniere was something like that--lol

    Geez-oh-man I really miss America like it used to be...

    It's kind of fun to do the impossible

  4. #4
    Join Date
    Jun 2007
    Location
    Oceanside, So. Calif. 5 mi. to the ocean
    Posts
    4,944
    If I call it a jardiniere stand will my plants live longer?

    Neat looking stand. It would go well in the Craftsman type of interior design.

    Enjoy,
    JimB
    First of all you have to be smarter than the machine.
    VOTING MEMBER

  5. #5
    Join Date
    Dec 2008
    Location
    falcon heights, minnesota
    Posts
    5,610
    i don't know about that jim, since i am the holder of all time record of english ivy plants killed (3 of them). after the warm up with the soup stir stick, got to work on the jardiniere stand. got the tenons on the legs cut, then the mortises. after that it was on to the upper supports. cut the notches and tenons, then cut the arcs and sanded them to the lines. after a quick test fit of the upper supports, and upper supports with the legs (i know, i know, looks kind of wobbly), then it was on to cutting the mortises in the feet, and the half laps. those were fun, as the one could be done with the router (with a prior pass on the table saw to establish where not to go), and the other was a combination router (to get what i could) and table saw (to get what i couldn't). then it was a final test fit of the base, and plopped the top on it to see how it would look. now all that is left for this is to sand everything to 220, and finish it the same as the clock.
    Attached Thumbnails Attached Thumbnails 011 tenons cut.jpg   012 mortises cut.jpg   013 notches and tenons cut.jpg   014 arcs cut and sanded.jpg   015 test fit of supports.jpg  

    016 test fit of legs and supports.jpg   017 mortises cut in feet.jpg   018 half laps cut in feet.jpg   019 test fit of legs feet and supports.jpg   020 test fit of base and top.jpg  

    benedictione omnes bene

    www.burroviejowoodworking.com

    check out my etsy store, buroviejowoodworking

  6. #6
    Join Date
    Dec 2008
    Location
    falcon heights, minnesota
    Posts
    5,610
    squeezed in a couple of hours on this one today. got all of the parts sanded to 220 and dyed. next steps are the sealcoat, gel stain, sealcoat, 3 coats of clear shellac, paste wax, then final assembly.
    Attached Thumbnails Attached Thumbnails 021 all parts sanded.jpg   022 all parts dyed.jpg  
    benedictione omnes bene

    www.burroviejowoodworking.com

    check out my etsy store, buroviejowoodworking

  7. #7
    Join Date
    Jul 2011
    Location
    The Gorge Area, Oregon
    Posts
    4,699


    Quote Originally Posted by Dan Noren View Post
    i don't know about that jim, since i am the holder of all time record of english ivy plants killed (3 of them).
    Didn't even know you could kill those! At least the ones in the yard sure don't seem to die for nothing.

  8. #8
    Join Date
    Jun 2008
    Location
    GTA Ontario Canada
    Posts
    12,258
    Looking good Dan is this white Oak you using? Are you planning on knocking down the sharp edges on the top side?
    cheers

  9. #9
    Join Date
    Apr 2007
    Location
    No, not all of SoCal is Los Angeles!
    Posts
    9,076
    Looking good. Can't wait to see it after finishing.
    Any sufficiently advanced technology is indistinguishable from magic.
    - Arthur C. Clarke

  10. #10
    Join Date
    Dec 2008
    Location
    falcon heights, minnesota
    Posts
    5,610
    yup, that's white oak, and nope, just about able to shave with those edges.
    benedictione omnes bene

    www.burroviejowoodworking.com

    check out my etsy store, buroviejowoodworking

Similar Threads

  1. Stand by me.
    By Rob Keeble in forum Off Topic Discussion
    Replies: 7
    Last Post: 03-02-2011, 11:21 PM
  2. tv stand
    By Dan Noren in forum Flatwork Project Showcase
    Replies: 6
    Last Post: 10-03-2010, 11:35 PM
  3. W.I.P. - TV stand
    By Bryan Cowing in forum Flatwork Project Showcase
    Replies: 26
    Last Post: 03-15-2010, 11:22 AM
  4. TV stand
    By Al killian in forum Flatwork Project Showcase
    Replies: 5
    Last Post: 08-06-2009, 01:00 PM
  5. T.V. stand
    By Al killian in forum Designs, Plans and Sketches
    Replies: 4
    Last Post: 05-26-2009, 10:19 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •