Page 1 of 2 12 LastLast
Results 1 to 10 of 13

Thread: Back at it

  1. #1
    Join Date
    Aug 2008
    Location
    Reno, Nv
    Posts
    3,632

    Back at it

    Been a little burned out on turning, but someone challenged me indirectly...so there!!
    Stabilized buckeye burl with an aluminium segment on a Sierra Vista, about 10 coats of CA...my finish work needs work! Thanks for looking!
    Attached Thumbnails Attached Thumbnails BEB.jpg  
    Your Respiratory Therapist wears Combat boots

  2. #2
    Join Date
    Dec 2008
    Location
    falcon heights, minnesota
    Posts
    5,610
    Good 'in Jim!
    benedictione omnes bene

    www.burroviejowoodworking.com

    check out my etsy store, buroviejowoodworking

  3. #3
    Join Date
    Mar 2007
    Location
    Escondido, CA
    Posts
    5,176
    Want a mailing address for your bad finish work?
    ++++++

    Some say the land of milk and honey; others say the land of fruits and nuts. All together my sort of heaven.

    Power is not taken. It is given. Who have you given yours to? Hmmmm?

    Carol Reed

  4. #4
    Join Date
    Dec 2006
    Location
    Yorktown, Virginia
    Posts
    5,022
    Pretty snazzy, Jim....must be like riding a bicycle

  5. #5
    Join Date
    Apr 2008
    Location
    Independence MO
    Posts
    561
    You need Stu to come over and film you for Youtube. Carol can bring the popcorn. I am just waiting for the video and some tools to get here (turner friend on another board, retiring due to health) and time to start learning. (downloaded and saved Stu's video for later watching; getting ready for some OT)

  6. #6
    Join Date
    Aug 2007
    Location
    Reno NV
    Posts
    13,365
    Sweet looking pen!
    Programmer - An organism that turns coffee into software.
    If all your friends are exactly like you, What an un-interesting life it must be.
    "A door is what a dog is perpetually on the wrong side of" Ogden Nash


  7. #7
    Join Date
    Jul 2009
    Location
    Amherst, New Hampshire
    Posts
    10,606
    very impressive
    Faith, Hope & Charity

  8. #8
    Join Date
    Nov 2006
    Location
    Delton, Michigan
    Posts
    17,476
    Good un Jim
    If in Doubt, Build it Stout!
    One hand washes the other!
    Don't put off today till tomorrow!

  9. #9
    Join Date
    Apr 2009
    Location
    Red Deer, Alberta, Canada
    Posts
    1,083
    Nice choice of component plating to complement the aluminum.
    A bit hard to see much detail or finish with such a small photo.

    Les
    Innovation is the process that renews something that already exists and not, as is commonly assumed, the introduction of something new.

  10. #10
    Join Date
    May 2007
    Location
    Thomasville, GA
    Posts
    6,000
    Mighty purty pen, Jim!
    Bill Arnold
    Citizen of Texas residing in Georgia.
    NRA Life Member and Member of Mensa
    My Weather Underground station

Similar Threads

  1. Back from Reno...back in the shop
    By Jim Burr in forum Lathe Project Showcase
    Replies: 4
    Last Post: 06-27-2013, 07:40 AM
  2. Bob is Back!
    By Brent Dowell in forum Off Topic Discussion
    Replies: 7
    Last Post: 08-04-2012, 02:35 PM
  3. Lakers Go Back-To-Back
    By Vaughn McMillan in forum Off Topic Discussion
    Replies: 16
    Last Post: 06-19-2010, 12:56 AM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •