Results 1 to 5 of 5

Thread: inspired by roger tulk

  1. #1
    Join Date
    Dec 2008
    Location
    falcon heights, minnesota
    Posts
    5,610

    inspired by roger tulk

    roger, you have inspired me to a good use for the extra walnut that i have on hand. stopped by the local lumber supplier to rummage around in his bins of off cuts for some maple. i hope to have 3 of them done for the upcoming craft shows. they will be roughly 18 inches deep by 20 inches wide.
    Attached Thumbnails Attached Thumbnails 001 maple for pastry boards.jpg   002 walnut for pastry boards.jpg  
    benedictione omnes bene

    www.burroviejowoodworking.com

    check out my etsy store, buroviejowoodworking

  2. #2
    Join Date
    Feb 2012
    Location
    St. Catharines, Ontario, Canada
    Posts
    2,749
    When I saw the thread title I thought, "Oh, God, what have I done now?" But I'm glad to see you took up the pasta board idea. They go from 50 up to 300 dollars on some sites. I'll have to build a few. I need to pay for a dado set.
    Cheers,
    Roger


    The other member of Mensa, but not the NRA

    Everyone is a self-made person.

    "The thing about quotes on the internet is that you cannot confirm their veracity" -Abraham Lincoln

  3. #3
    Join Date
    Dec 2008
    Location
    falcon heights, minnesota
    Posts
    5,610
    got a bit more done on these, got all of the maple and walnut planed, and ripped to width. today i cut everything to length, glued up the hard maple, and rounded over the walnut ends.
    Attached Thumbnails Attached Thumbnails 003 parts planed for pastry boards.jpg   004 first board in clamps.jpg   005 walnut ends cut to length and rounded over.jpg   006 second board in clamps.jpg  
    benedictione omnes bene

    www.burroviejowoodworking.com

    check out my etsy store, buroviejowoodworking

  4. #4
    Join Date
    Dec 2008
    Location
    falcon heights, minnesota
    Posts
    5,610
    been a bit since i worked on this one, but worked on it i did today. got the end parts glued on, and brought home so i can sand and oil them as i have time.
    Attached Thumbnails Attached Thumbnails 007 edge part glued to first board.jpg   008 edge part glued to second board.jpg   009 second edge part glued to first board.jpg   010 second edge part glued to second board.jpg  
    benedictione omnes bene

    www.burroviejowoodworking.com

    check out my etsy store, buroviejowoodworking

  5. #5
    Join Date
    Dec 2008
    Location
    falcon heights, minnesota
    Posts
    5,610
    finish sanded and oiled both boards, another one in the books.
    Attached Thumbnails Attached Thumbnails 011 both boards sanded.jpg   012 board 1 oiled.jpg   013 board 2 oiled.jpg  
    benedictione omnes bene

    www.burroviejowoodworking.com

    check out my etsy store, buroviejowoodworking

Similar Threads

  1. Happy Birthday Roger Tulk
    By Ken Cook in forum Off Topic Discussion
    Replies: 19
    Last Post: 03-04-2015, 09:39 PM
  2. Happy B-Day Roger Tulk
    By Ken Cook in forum Off Topic Discussion
    Replies: 17
    Last Post: 03-05-2014, 03:47 AM
  3. Welcome Angus Iain Webster Tulk!
    By Roger Tulk in forum Off Topic Discussion
    Replies: 18
    Last Post: 09-08-2013, 01:08 PM
  4. Happy Belated to Roger Tulk!
    By Darren Wright in forum Off Topic Discussion
    Replies: 10
    Last Post: 03-05-2013, 11:55 AM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •