Results 1 to 7 of 7

Thread: Vcarve 8.5

  1. #1
    Join Date
    May 2007
    Location
    Kansas City, Missouri
    Posts
    13,464

    Vcarve 8.5

    Anyone downloaded vcarve 8.5 yet?

    Sent from my SM-G920P using Tapatalk
    Darren

    To a small child, the perfect granddad is unafraid of big dogs and fierce storms but absolutely terrified of the word “boo.” – Robert Brault

  2. #2
    Join Date
    May 2007
    Location
    Thomasville, GA
    Posts
    6,000
    Yep. I downloaded and installed it on June 2. No problems so far. VCarve Pro.
    Bill Arnold
    Citizen of Texas residing in Georgia.
    NRA Life Member and Member of Mensa
    My Weather Underground station

  3. #3
    Join Date
    Feb 2008
    Location
    East Freeetown, Massachusetts
    Posts
    3,022
    I downloaded 8.5

    No problems.

  4. #4
    Join Date
    May 2007
    Location
    Kansas City, Missouri
    Posts
    13,464
    Cool, will give it a shot...thanks!

    Sent from my SM-T710 using Tapatalk
    Darren

    To a small child, the perfect granddad is unafraid of big dogs and fierce storms but absolutely terrified of the word “boo.” – Robert Brault

  5. #5
    Join Date
    Dec 2008
    Location
    falcon heights, minnesota
    Posts
    5,610
    Same here, I have it too. Works good for me.
    benedictione omnes bene

    www.burroviejowoodworking.com

    check out my etsy store, buroviejowoodworking

  6. #6
    Join Date
    May 2007
    Location
    Kansas City, Missouri
    Posts
    13,464
    Upgraded! I noticed it left the 8.0 version installed too. I haven't uninstalled it, keeping it just in case I need to save back with that version for some reason.
    Darren

    To a small child, the perfect granddad is unafraid of big dogs and fierce storms but absolutely terrified of the word “boo.” – Robert Brault

  7. #7
    Join Date
    Feb 2008
    Location
    East Freeetown, Massachusetts
    Posts
    3,022
    I have upgraded Vectric many times since 2007.

    Never have needed to go backward compatible yet.

Similar Threads

  1. playing with vcarve demo
    By Dan Noren in forum Programming, Troubleshooting, and Q&A
    Replies: 2
    Last Post: 01-09-2016, 05:55 PM
  2. Adding profiles to vcarve
    By Darren Wright in forum Programming, Troubleshooting, and Q&A
    Replies: 2
    Last Post: 11-27-2015, 01:27 PM
  3. V-Inlays in VCarve
    By Darren Wright in forum Computer-Aided Equipment Project Showcase
    Replies: 6
    Last Post: 10-29-2015, 04:58 AM
  4. How-To: The Router Bit Organizer in vCarve
    By Darren Wright in forum Programming, Troubleshooting, and Q&A
    Replies: 4
    Last Post: 09-29-2015, 03:50 PM
  5. Laser with vCarve Desktop and Mach3
    By Darren Wright in forum Computer-Aided Equipment Project Showcase
    Replies: 13
    Last Post: 09-01-2015, 03:21 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •