Results 1 to 9 of 9

Thread: Hey Vaughn.....

  1. #1

    Exclamation Hey Vaughn.....

    Vaughn,

    I'm going to lunch with some folks from FWW and SMC tomorrow. Could you measure the width and depth of the groove for your miter gauge groove on your TS3650 please?

    I might buy a tenoning gauge for my TS3650 at Rockler tomorrow. Having those measurements might keep me from sending it back.

    Thanks V!

    Ken
    Ken
    ------



  2. #2
    Join Date
    Oct 2006
    Location
    ABQ NM
    Posts
    30,020
    Ken, it's about 3/4" wide and a little shy of 7/16" deep. (Specifically, 0.758 and 0.425 inches, respectively.) Any standard accessory made for a 3/4" wide slot should work. I believe 3/8" is the standard minimum depth, so this one has room to spare depth-wise. I'd be willing the bet the Rockler gauge will work fine.
    When the going gets weird, the weird turn pro. - Hunter S. Thompson
    When the weird get going, they start their own forum. - Vaughn McMillan

    workingwoods.com

  3. #3
    Thanks Vaughn! I'm in Dallas this week and next. A tenoning jig is high on my list of "Dear.......I gotta have......PRETTY.....PRETTY.....PRETTY............ please! things!

    I've been married 40 years, as a result I grovell well!
    Ken
    ------



  4. #4
    Join Date
    Nov 2006
    Location
    Between Aledo and Fort Worth, TX
    Posts
    2,784
    Hey Ken, I'll bring you an email coupon to use at this store. It has your name on it and everything! Jim.
    Coolmeadow Setters...
    Exclusively Irish!
    Home of Irish Setter Rescue of North Texas
    When Irish Eyes are smiling, they're usually up to something!!
    At a minimum, I'm Pentatoxic...but most likely, I'm a Pentaholic. There seems to be no known cure. Pentatonix, winners of The Sing Off, season 3


  5. #5
    Thanks Jim. Bring the coupon.

    Did you know you can grovel over the phone? My wife just closed her eyes and it didn't take too much imagination as she's seen the posture and heard the whine so many times before.

    I hope they can ship it for me.
    Ken
    ------



  6. #6
    Join Date
    Nov 2006
    Location
    Oak Harbor Washington on Whidbey Island
    Posts
    3,134
    Quote Originally Posted by Ken Fitzgerald View Post
    Thanks Jim. Bring the coupon.

    Did you know you can grovel over the phone? My wife just closed her eyes and it didn't take too much imagination as she's seen the posture and heard the whine so many times before.

    I hope they can ship it for me.
    By her a nice bottle of it & some cheese & maybe crackers too,
    "Forget the flat stuff slap something on the spinny thing and lets go, we're burning daylight" Bart Leetch
    "If it ain't round you may be a knuckle dragger""Turners drag their nuckles too, they just do it at a higher RPM"Bart

  7. #7
    Quote Originally Posted by Bart Leetch View Post
    By her a nice bottle of it & some cheese & maybe crackers too,
    Uh Bart......I didn't say she like the taste of it.....she just caved in.....got tired of it!
    Ken
    ------



  8. #8
    After lunch with a neat bunch of woodworkers,

    I bought that tenoning jig. I'll blame Jim O'Dell for that. If he hadn't had the coupon, I'd have turned it down. Don't worry Jim.....Sharon doesn't have your address!
    Ken
    ------



  9. #9
    Join Date
    Nov 2006
    Location
    Between Aledo and Fort Worth, TX
    Posts
    2,784
    Hey, you could have thrown the coupon away!!
    But you can tell Sharon that you got a free corner clamp thingie to boot! Jim.
    Coolmeadow Setters...
    Exclusively Irish!
    Home of Irish Setter Rescue of North Texas
    When Irish Eyes are smiling, they're usually up to something!!
    At a minimum, I'm Pentatoxic...but most likely, I'm a Pentaholic. There seems to be no known cure. Pentatonix, winners of The Sing Off, season 3


Similar Threads

  1. Vaughn, I .....
    By Al Launier in forum Off Topic Discussion
    Replies: 1
    Last Post: 10-24-2013, 05:01 PM
  2. Hey Vaughn
    By Dan Mooney in forum Off Topic Discussion
    Replies: 2
    Last Post: 07-09-2013, 05:05 AM
  3. Vaughn, you okay?
    By Jim DeLaney in forum Off Topic Discussion
    Replies: 17
    Last Post: 12-21-2010, 06:53 AM
  4. Hey, Vaughn
    By Gord Rock in forum General Woodturning Q&A
    Replies: 2
    Last Post: 01-08-2008, 04:27 AM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •